Latest Case Mods

Case Mods Now Available!

How to use your Rapid Fire Controller

To use this controller:
Link the controller to your xbox (first time using controller)
Press and hold the button on the top of the controller until the lights on the front spin.

Press the controller link button on your xbox console.
To use rapid fire:
Press the sync button on the top of the controller – press it do not hold it
This switches modes, there are three modes, for each mode the light on the front of the controller will blink to indicate which mode it is in.
Modes:
Mode 1 - Halo 3, COD 4 - Super Fast

Mode 2 - COD 4 - Insanely Fast!

Mode 3 - COD 5, GOW - Rated speed for COD 5 at 8.33 Shots per second

Mode 3 is for COD 5 Online play (and single player). When using this mode you can not hold on the rapid fire button for more that 10-15 seconds or the game will still detect you, the best way to avoid COD detection is to burst fire when needing to fire, and when your gun is reloading do not hold on the trigger! If you follow these simple steps you will have a good experience online! Also – fully automatic weapons fire slower with rapid fire engaged – this decreases your rate of fire but improves accuracy
by decreasing recoil!

Please email if you have any questions

SBConsoleMods@Gmail.com

Identify your Xbox 360 controller type here first!

The Matrix style controller has two square chips on it and the CG has one that is in a diamond shape. The top picture is the CG style and the bottom one is the Matrix style. Check the picture to verify which one is yours and move on to the next step.
If you have any questions please email SBConsoleMods@Gmail.com




Rapid Fire Modes
Mode 1 - Halo 3 (Dual Trigger is Optional)
Mode 2 - Call of Duty 4
Mode 3 - Call of Duty 5

Xbox 360 Rapid Fire Tutorial For CG Style Controller

This guide has pictures of the step by step process to install your Rapid Fire Chip. If you have any questions please email SBConsoleMods@Gmail.com

Helpful tips:
Use 30 Gauge Wire
15 Watt Soldering Iron
Use rosin core solder, 60/40 works great
Always use fresh solder for every solder point
Use a wet sponge to take off old solder
Strip only 1/8 to 1/4 inch of wire
Add solder to ends of wire for better contact
Keep wires away from holes and controller buttons



























































If you want dual trigger rapid fire for Halo 3, then you must add a 5.5 inch wire to pin 6. If you don't play Halo 3, then this will not be needed.

Here are the pictures for making the left trigger Rapid fire for Halo 3 in Mode 1

Guide for the Matrix style Rapid Fire Sleeper chip

This guide has pictures of the step by step process to install your Rapid Fire Chip. If you have any questions please email SBConsoleMods@Gmail.com

Helpful tips:
Use 30 Gauge Wire
15 Watt Soldering Iron
Use rosin core solder, 60/40 works great
Always use fresh solder for every solder point
Use a wet sponge to take off old solder
Strip only 1/8 to 1/4 inch of wire
Add solder to ends of wire for better contact
Keep wires away from holes and controller buttons


Make sure your board looks like this before moving on.



Cut 5 wires to the following length as listed.





The top side of the chip has a notch, hot glue that side towards the bottom.







Solder 4.5 inch wire to point






Solder 2.5 inch wire to first post








Solder 1.5 inch wire to bottom point of LED




Solder 5.5 inch wire to first hole












Solder 3 inch wire to the ground like in the picture and solder the other end to pin 8.





If you want Dual trigger for Halo 3 in Mode 1, you must add a 6 inch wire and a resistor to pin 6. If you do not play Halo 3, then you will not need to do this.